Technical Data Sheet - Page 03
HI-PURITY CONTACT CLEANER
Description
A carefully selected, high quality halogenated hydrocarbon solvents propelled by F134A. The product offers maximum degreasing performance. Removes accumulations of grease, oil and dirt from electronic parts with no residue. The aerosol's rapid jet stream helps the cleaning process, while giving pinpoint penetration. The aerosol can be sprayed in any direction. The product is non-flammable and non-conductive.
Use/Benefits
Use on all types of electrical contacts, switches and relays to remove film and unwanted material. Can also be used as a flux remover. Removes light grease, oils, dirt and organic soils.
DIRECTIONS FOR USE
DISENGAGE AND DE-ENERGIZE EQUIPMENT. ALWAYS OBSERVE OSHA ELECTRICAL LOCK AND TAG OUT PROCEDURES. For cleaning large areas, use the standard spray head. For pinpoint spray, use extension tube. Hold 2 to 4 inches from area to be cleaned, and spray in short bursts. Keep can upright while spraying. Do not spray on hot surfaces. For best results, use at room temperature. Avoid use on certain plastics including ABS, PET, acrylic, polycarbonate, and polystyrene. Test on surface before using.
Physical Properties
| Appearance | Clear, colourless |
| Specific Gravity (Aerosol, @ 21oC) | 1.39 +- 02 |
| pH (@ 25oC) | Not Applicable |
| Non-Volatile (Aerosol, % by wt) | 0% |
| Vapour Pressure (@ 21oC) | 60 to 70 psig |
| Spray Pattern (@ 21oC) | Narrow, Conical |
| Spray Rate (10 s, @ 21oC) | |
| Actuator | 30-35 g/10s |
| X-tube | 11-15 g/10s |
| Volatile Organic Compounds (VOC, %w/w) | 1-2% |
OUTSTANDING PROPERTIES
- Fast Penetration, Evaporation.
- Reduces contact resistance.
- Leaves contacts clean and dry, with no film residue.
- Nonconductive. Non-flammable. No flash or fire point.
- Safe to use on most surfaces.
- Multi-Directional spray valve.
LABEL INFORMATION
WHMIS: A, D2B
HAZARD STATEMENT (S)
Skin, Eye Irritant.
Contents under pressure.
ADDITIONAL HAZARD STATEMENTS
Keep away from heat, sparks and flame. Avoid contact with eyes, skin and clothing. Use only with adequate ventilation. Do not puncture or incinerate container or store at temperatures over 50C.
FIRST AID TREATMENT
In case of eye contact, flush immediately with plenty of water for at least 15 minutes and get medical attention. For skin, wash thoroughly with soap and water. If affected by inhalation of vapour or spray mist, remove to fresh air. If swallowed, get medical attention. Contains 1, 1, 1, 2-Tetrafluoroethane.
SEE MATERIAL SAFETY DATA SHEET.
Codes
| 12 x 454 grams per case | BT 303 |
FOR HEALTH AND SAFETY INFORMATION REFER TO THE APPROPRIATE MSDS
The information herein is to assist customers in determining whether our products are suitable for their applications. We request that customers inspect and test our products before use, and satisfy themselves as to contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is protection from any law or patent inferred.
AIR DUSTER
Description
A non-flammable, non-toxic, non-VOC propellant (Tetrafluoroethane)
packaged in a TDG/DOT approved Sexton can (TC SU-5016 NRC/DOT-E-10232) – for handling safety.
Use/Benefits
Air Duster is a high powered product which can be used to remove dust and airborne
contamination from all electrical and electronic equipment, e.g. computers, keyboards and
other office equipment. It can also be used on items such as cameras and audio
components. It can also be used to evacuate air from the top of cans of paint to stop
skin forming. It may also be used in drying operations after cleaning to remove residue
moisture.
DIRECTIONS FOR USE
The can must be held in an upright position while spraying. Before use, press the actuator
to clear the valve. Point nozzle in the desired direction. Check the owner’s manual before
using on valuable equipment.
Physical Properties
| Appearance | Clear, Colourless Gas |
| Specific Gravity (@ 21oC) | 1.22 ± 0.02 |
| pH (@ 25oC) | Not Applicable |
| Non-Volatile (Aerosol, % by wt) | 0% |
| Vapour Pressure (@ 21oC) | 65 – 75 psig |
| Spray Pattern (@ 21oC) | Not Applicable |
| Spray Rate (10 s, @ 21oC) | Not Applicable |
OUTSTANDING PROPERTIES
- Non-flammable
- Maximum user safety.
- Ozone safe
LABEL INFORMATION
WHMIS: A
PRIMARY HAZARD STATEMENTS(S)
Container may explode if heated.
ADDITIONAL HAZARD STATEMENTS
Contents under pressure. Do not place in hot water or near radiators, stoves, or other sources of heat. Do not puncture or incinerate container or store at temperatures over 50oC.
RECOMMENDED SIZING:
| 211 x 503 Sexton | 285 g |
FOR HEALTH AND SAFETY INFORMATION REFER TO THE APPROPRIATE MSDS
The information herein is to assist customers in determining whether our products are suitable for their applications. We request that customers inspect and test our products before use, and satisfy themselves as to contents and suitability. Nothing herein shall constitute a warranty, expressed or implied, including any warranty of merchantability or fitness, nor is protection from any law or patent inferred.
Codes
| 12 x 285 grams per case | BT308 |